Short Description: Flash drive tool for Lite-On drives. Submitted By. Problem with a Jumperless LiteOn drive. I used the tool (XSF-1.53). But a message appeared that the tool can't enter flash mode.

1. Sp Flash Tool

Flash Utility for LiteOn Based Optical Drives Formerly known as Flash Reader The Official Thread What is it Flash Utility is a tool to allow the reading and writing of the firmware Flash, in Windows, for almost all LiteOn based drives. Well as you have probably seen, this tool is now called the Flash Utility. The reason for this is because this tool can now write the Flash as well as read it. When I first started this tool I wasn't sure that I would be able to do the writing side of it, as it's quite an involved process.

LiteOn wisely didn't limit themselves to one manufacturer's flash part in a model, like some of the other drive manufactures, so the flasher has to download a special flash writer to the drive that supports the Flash part installed, hence the reason for the Flash ID. But I'm not one to let a challenge beat me too easily, in fact it tends to make me more determined, so here it is. It should support a lot of what LtnFW supported plus all of the new flash parts, that I know of, as well. Features: Reading of Flash Writing of Flash Supports firmware BIN files and unscrambled Flasher EXE files Supports up to 8MB reading Supports up to 2MB writing Auto learning of Flash ID and size for reading Multi-threaded operation for write progress display How to do a Flash read Select the drive from the drop down list that you want to read the firmware from. Wait a few seconds while the drive checks the Flash type used in the drive. 50+ Flash IDs have already been incorporated into the Flash Reader utility, which will cover most of the 1MB and 2MB parts currently being used, but to protect the future usability of the program I have incorporated a learning feature for new and older Flash parts and allowed up to 8MB reads. If the flash is known then you will be returned to the first screen shown above with the correct Flash size set.

If it is not known then the following dialog will be displayed. This indicates that the Flash ID was unknown and that the true size of the flash has had to be calculated. Please check that the size that has been selected for your drive is correct. If it is incorrect, adjust the size and save the new size by clicking on the blue Flash ID as shown below.

Once you are happy that the drive and size are correct, just click the 'Read Flash' button, enter a file name or accept the default and then wait for the read to finish. This can take up to two minutes for a 2MB flash. If you get an error during the read, this is usually an indication that the flash size was set too large. The progress bar is a good indicator of how large the Flash actually is. If it has only progressed to half way then the Flash size is set to twice what it should actually be. Try setting the flash size to half of what it is currently set to and save it using the method explained above.

In saying all of that, if my calculate Flash size routine works as I think it should, then this should never be required. Now if only it was as easy to flash the drive. Well it wasn't easy but I've done it.phew - wipes sweat from brow. How to do a Flash write The Flash Utility can also write the flash in most LiteOn based drives. This is an advanced feature and should be used with caution.

Sp Flash Tool

No checking of whether the firmware matches the hardware is carried out, so if you select the wrong firmware for your drive then the drive could end up being dead. Of course the drive can be restored by using MTKFlash or XSF if your drive uses a serial flash.

If the 'Write Flash' button and 'Update boot code' check box is enabled then you can flash the currently selected drive. The 'Flash Size' list is ignored for writing and instead the size of the binary file is used. The Flash utility does check that the bin file provided is one of the allowable sizes e.g. 128KB,256KB.2MB, so if you select a flasher file by mistake, you will get an error.

You can also specify an unscrambled Flasher EXE file, which you will finds on my site here: Guys. The Flash Utility will extract the firmware from the flasher file and write it to the drive. This may save you having to locate a binary file for your drive. Click the 'Write Flash' button to start the write process.

A message box is displayed warning you of the dangers of using this function. Please make sure you have the right drive selected at this point. Click the 'Yes' button to continue and then select the require BIN file or Flasher EXE file to flash the drive with. To select a Flasher EXE file use the 'Files of Type' dropdown list on the Open dialog to select 'Executable files'. A last chance warning will now be displayed showing the selected drive, the selected file and the state of the update boot code option.

Click the 'Yes' button if you are sure everything is a it should be and the Flash write will begin. This process cannot be aborted at this point.

The progress bar will move during the entire burn but in some rare cases may reach 100% before the write process is complete. I've handled the very slow flash chip used in the 1653S series (MX29LV008B), which takes 3x as long to write than most Flash parts, since I was unfortunate enough to get one in my drive. Also during the write Flash process, at the exact point that the flash is being erased/written 'Writing.'

Will appear flashing on the display. Until this stops flashing the write is still being carried out, so don't interrupt the process in any way. When the Flash write is complete the drive list will be updated with the new version running in the drive, so you will know that all is well. Another little feature I've added is a quick method to get to my site to check for updates.

Just click on the CodeGuys graphic on the bottom of the application and your default browser will direct you to my site. Credits Special thanks goes to and (The Firmware Page) and the authors of Dvdzone and PLScsi, xvi, Pat LaVarre and r-man. Without them, this utility would not have been possible. Version: v6.0.1 (18 February 2011 - Final release).

Supports more drives, including all of the B series drives. Fixed - Pioneer drives could cause the app to hang at start up Version: v5.0.0. Changes to the SCSI driver.

Flash timing changes, for faster systems. Fixed bug when flashing LiteOn to Plextor and then back to LiteOn, without closing FU or selecting another drive.

Brainfuck-Quellcode. DosFlash and DosFlash32 V1. Brainfuck-Quellcode. DosFlash and DosFlash32 V1. 4 Beta. DROM6316 flashing support. a flash erase is now always done with a chip erase and not a sector erase command, because.

the sector erase gives problems for some Winbond flash chips including the DROM6316. DosFlash.

Typ corrected and updated. for a detailed explanation on the soft unlock look at the included file SoftUnlockByIriez. Txt,. it contains a very good explanation by Iriez from XBS, thanks for that one!.

Thanks to Iriez, Jumba, Redline99 and Tiros for help and support. Happy DROM bricking!. Team Modfreakz and Kai Schtrom Alles anzeigen xbins.org.

Und hab dann auch noch die FW v1.4 version Firmware: - ix14-12 FirmTool Make Ixtreme Firmware. So meine frage muss das alles auf eine diskett gespeichert werden oder nur die Firmware - ix14-12. Weil lese immer was von DOSFlash 1.3 aber weiss nicht genau ob es das jetzt oder nicht k.a kann einer mir sagen was genau ich auf die diskett legen muss. Du scheinst da ziemlich planlos ranzugehen, da ist dein Laufwerk schneller zerflasht als du schauen kannst. Hast du icq?? Wenn ja dann adde mich mal ich schick dir per ICQ alles was du brauchst.